Frame-Relay connection

Posted by Belajar cisco untuk pemula on

Friday, May 20, 2016

Frame-Relay connection

Task 1: Frame-Relay Point-to-Point subinterface

Router-SBY:

(config)# int serial 0/1

(config-if)# no ip address

(config-if)# encapsulation frame-relay 

(config-if)# int s0/1.100 point-to-point

(config-subif)# ip address 10.1.2.2 255.255.255.0

(config-subif)# frame-relay interface-dlci 100

(config-subif)# bandwidth 2048

(config-subif)# end 

# copy run start

Router-MDN:

(config)# int serial 1/0

(config-if)# no ip address

(config-if)# encapsulation frame-relay 

(config-if)# int s1/0.200 point-to-point

(config-subif)# ip address 10.1.2.1 255.255.255.0

(config-subif)# frame-relay interface-dlci 200

(config-subif)# bandwidth 2048

(config-subif)# end 

# copy run start

Verify (all routers):

# sh frame-relay map

# sh frame-relay pvc

# sh frame-relay lmi

# sh int serial s0/1            è  di SBY

# sh int serial s1/0            è  di MDN 

# debug frame-relay lmi

# terminal monitor 

# sh ip route

# ping ….

     

FRS config:

(config)# frame-relay switching 

(config)# default int s0/0

(config)# default int s0/1 

(config)# int s0/0

(config-if)# desc *** to Router-MDN ***

(config-if)# encap frame-relay

(config-if)# frame-relay intf-type dce

(config-if)# frame-relay route 200 int s0/1 100    à frame-relay route [input DLCI] [output intf] [output DLCI]

(config-if)# clock rate 2000000

(config-if)# bandwidth 2048

(config-if)# no shutdown 

(config)# int s0/1

(config-if)# desc *** to Router-SBY ***

(config-if)# encap frame-relay

(config-if)# frame-relay intf-type dce

(config-if)# frame-relay route 100 int s0/0 200    à frame-relay route [input DLCI] [output intf] [output DLCI]

(config-if)# clock rate 2000000

(config-if)# bandwidth 2048

(config-if)# no shutdown

Task 2: Frame-Relay multipoint subinterface

Router-SBY:

(config)# no int s0/1.100 point-to-point è hapus point-to-point subinterface 

(config)# int serial 0/1

(config-if)# no ip address

(config-if)# encapsulation frame-relay 

(config-if)# int s0/1.1 multipoint

(config-subif)# ip address 10.1.2.2 255.255.255.0

(config-subif)# frame-relay map ip 10.1.2.1 100 broadcast

(config-subif)# bandwidth 2048

(config-subif)# end 

# copy run start

Router-MDN:

(config)# no int s0/1.100 point-to-point è hapus point-to-point subinterface 

(config)# int serial 1/0

(config-if)# no ip address

(config-if)# encapsulation frame-relay 

(config-if)# int s1/0.1 multipoint

(config-subif)# ip address 10.1.2.1 255.255.255.0

(config-subif)# frame-relay map ip 10.1.2.2 200 broadcast

(config-subif)# bandwidth 2048

(config-subif)# end 

# copy run start